Gripdeck WEARCOAT
Previous product
Next product
Gripdeck WEARCOAT PLUS
 

Gripdeck
WEARCOAT TG

SOLVENT FREE FLEXIBLE POLYURETHANE WEAR COURSE
 
Description:

Gripdeck Wearcoat TG is a two-part, solvent free, flexible polyurethane wearing course formulated for easy application by squeegee, roller or brush onto an aggregate blinded surface.

Usage

Gripdeck Wearcoat TG is designed specifically for use in warmer climates to give excellent abrasion and non-slip characteristics when combined with Quartz or Gripdeck Aggregate.

Gripdeck Wearcoat TG is primarily designed for use in car parks and offers excellent chemical resistance against petrol, battery acids, diesel, brake fluids, decing salts, etc.

Materials Supplied

15kg pack size comprising Resin base and Hardener components. 

Coverage

The coverage obtained will vary depending on the type and size of aggregate used. As a guide the coverage should be a minimum of 0.8kg per m² on a Quartz Aggregate blind and 1.2kg per m² on a Gripdeck Aggregate blind.

Storage

Store under dry warehouse conditions at a temperature between 10°C and 30°C.

Shelf Life

12 month in unopened, undamaged, sealed containers and stored under good conditions.

Technical Information

Working time @ 20°C20 minutes
Tack free time @ 20°C8 hours
Maximum overcoating time at 20°C24 hours
Full Cure @ 20°C
3 days
Tensile strength (N/mm2)
10
Hardness (Shore D)75
Wear resistance
ASTM C501,
 CS17 wheels, 1000 cycles,
1Kg weight
0.3g weight loss
Application Temperature Range (°C)
(do not apply if precipitation or
condensation is likely to result)
15 to 35
Volume solids (%)100
Slip resistance - typical
figures BS 7976, Part 2 : 2002
Coarse Quartz
Aggregate blind
TRL slider: 84 dry, 72 wet
4-S slider: 61 dry, 53 wet

Coarse Gripdeck
Aggregate blind
TRL slider: 90 dry, 64 wet
4-S slider: 99 dry, 75 wet

Application Instructions

SURFACE PREPARATION

For details please see the DCP Guide to Surface Preparation.

MIXING 

Gripdeck Wearcoat TG comprises two components, a Resin base and Hardener, which are supplied pre-weighed in the correct proportions. Under no circumstances should part mixing be carried out.

Taking care to ensure that the bottom and sides are thoroughly scraped, transfer the entire contents of both components into a separate mixing container. Using a power whisk attached to a slow speed electric drill, mix for approximately 3 minutes ensuring the the mixing head is pushed around the sides and bottom of the mixing container. Transfer the contents into another container, scraping down and re-mixing for a further 2 minutes avoiding the entraining of excessive air until a uniform consistency is obtained.

Never mix Gripdeck Wearcoat TG by hand as this could lead to areas of uncured material. Premixing of the material will aid mixing.

APPLICATION

On completion of mixing immediately apply the Gripdeck Wearcoat TG by short/medium pile roller or squeegee at the required thickness depending on requirements.

Gripdeck Wearcoat TG is not colour stable and may discolour on aging especially on lighter colours. This will not adversely affect the performance of the system.

Gripdeck Wearcoat Plus should be used where light colours or a UV colour stable system is required

CLEANING

Tools should be cleaned with Quickmast Solvent immediately after use.

HEALTH AND SAFETY

Consult the appropriate Material Safety Data Sheets prior to using Gripdeck Wearcoat TG.

GENERAL GUIDANCE
This data sheet is for general guidance purposes only and may contain information that is inappropriate for certain conditions of use. Accordingly, all recommendations and suggestions are made without guarantee. Further information is available from our Technical Department.


Download file




Connect with Don Construction Products


  Complaints Record Form

  Customer Satisfaction

Name *
Email *
Phone
Address
Subject
Request  
Security Code *

Don Construction Products Ltd.

Headquarters
Hawthorn House, Helions Bumpstead Road,
Haverhill CB9 7AA, United Kingdom;
Tel: +44 1 4407 66360 
Fax: +44 1 4407 68897

Email: sara.harvey@dcp-int.co.uk
Email: stephen.bird@dcp-int.co.uk