Gripdeck WEARCOAT TG
Previous product
Next product
Gripdeck SYSTEM
 

Gripdeck
WEARCOAT PLUS

SOLVENT FREE FLEXIBLE POLYURETHANE WEAR COURSE
 
Description:

Gripdeck Wearcoat Plus is a UV stable, two-part, solvent free, flexible polyurethane wearing course formulated for easy application by squeegee, roller or brush.

Usage

Gripdeck Wearcoat Plus is designed to give excellent abrasion and non-slip characteristics when combined with Quartz or Gripdeck Aggregate.

Gripdeck Wearcoat Plus is primarily designed for use in car parks and offers excellent chemical resistance against petrol, battery acids, diesel, brake fluids, de-icing salts, etc. Other applications include showrooms, retail, car dealerships etc.

Gripdeck Wearcoat Plus is specifically formulated for colour stability. It will not discolour on exposure to sunlight or other sources of UV light.

Materials Supplied

15kg pack size, comprising resin base and hardener components. 

Coverage

The coverage obtained will vary depending on substrate type and size of Aggregate, if used. 

As a guide, the coverage should be a minimum of:

0.8kg per m² on a Quartz Aggregate blind.

1.2kg per m² on a Gripdeck Aggregate blind.

0.3kg/m² on to smooth Strongcoat Primer.

Storage

Store under dry warehouse conditions at a temperature between 10°C and 30°C.

Shelf Life

12 months in unopened, undamaged, sealed containers and stored under good conditions.

Technical Information

Working time @ 15°C15 minutes
Tack free time @ 15°C6 hours
Full Cure @ 15°C3 days
Tensile strength (N/mm²)
9
Hardness (Shore D)
60
Application Temperature Range (°C)
(do not apply if precipitation or
condensation is likely to result)
10 to 30°C
(do not apply if
the ambient or
floor temperature
is to fall below
10°C during the
first 24 hours)
Volume solids (%)100
EN 13813 Designation
SR-AR0.5-B2.0-IR10
EN 1504-2 Principle
5 (PR)
Abrasion resistance
EN- 13892-4
≤ 50 μm
Thermal compatability (N/mm²)
EN 13687-1&2
≥ 1.5
Capillary absorption
EN 1062-3
≤ 0.1kg.m-2.h0.5
Crack bridging ability
EN 1062-7; Static
≥ 500 μm 
Impact resistance
EN ISO 6272-1
≥ 10 Nm
Adhesion by pull-off (N/mm²)
EN 1542
≥ 2.0
Slip/Skid resistance *
EN 13036-4
≥ 55 units wet

Application Instructions

MIXING 

Gripdeck Wearcoat Plus comprises two components, a Resin Base and Hardener, which are supplied, pre-weighed in the correct proportions. Under no circumstances should part mixing be carried out.

Taking care to ensure that the bottom and sides are thoroughly scraped, transfer the entire contents of both components into a separate mixing container. Using a power whisk attached to a slow speed electric drill, mix for approximately 3 minutes ensuring the mixing head is pushed around the sides and bottom of the mixing container. Transfer the contents into another container, scraping down and re-mixing for a further 2 minutes avoiding the entraining of excessive air until a uniform consistency is obtained.

Never mix Gripdeck Wearcoat Plus by hand as this could lead to areas of uncured material. Premixing of the resin component will aid mixing.

PRIMING (Car Parks)

Use Gripdeck Primecoat or Strongcoat DPM (please see appropriate product data sheets for more information).

PRIMING (Non Car Parks)

Surfaces must be primed with Strongcoat Primer. If the substrate humidity reading is greater than 75% it is recommended that Strongcoat DPM be used prior to priming with Strongcoat Primer (please consult appropriate data sheets).

APPLICATION OVER AGGREGATE

On completion of mixing immediately apply the Gripdeck Wearcoat Plus by squeegee followed by a short/medium pile roller at the required rate onto a pre-swept blinded surface.

APPLICATION ON TO A PRIMED BASE

Once mixing is complete transfer the Gripdeck Wearcoat plus to a roller tray, and using a medium pile simulated sheepskin roller, apply it evenly over the surface.

CLEANING

Tools should be cleaned with a suitable solvent immediately after use.

HEALTH AND SAFETY

Consult the appropriate Material Safety Data Sheets prior to using Gripdeck Wearcoat Plus.

GENERAL GUIDANCE
This data sheet is for general guidance purposes only and may contain information that is inappropriate for certain conditions of use. Accordingly, all recommendations and suggestions are made without guarantee. Further information is available from our Technical Department.


Download file



Related products





Connect with Don Construction Products


  Complaints Record Form

  Customer Satisfaction

Name *
Email *
Phone
Address
Subject
Request  
Security Code *

Don Construction Products Ltd.

Headquarters
Hawthorn House, Helions Bumpstead Road,
Haverhill CB9 7AA, United Kingdom;
Tel: +44 1 4407 66360 
Fax: +44 1 4407 68897

Email: sara.harvey@dcp-int.co.uk
Email: stephen.bird@dcp-int.co.uk