Gripdeck FLEXCOAT
Previous product
Next product
Gripdeck WEARCOAT TG
 

Gripdeck
WEARCOAT

SOLVENT FREE FLEXIBLE POLYURETHANE WEAR COURSE
 
Description:

Gripdeck Wearcoat is a two-part, solvent free, flexible polyurethane wearing course formulated for easy application by squeegee, roller or brush onto an aggregate blinded surface.

Usage

Gripdeck Wearcoat is designed to give excellent abrasion and non-slip characteristics when combined with Quartz or Gripdeck Aggregate.

Gripdeck Wearcoat is primarily designed for use in car parks and offers excellent chemical resistance against petrol, battery acids, diesel, brake fluids, de-icing salts, etc.

Materials Supplied

5kg and 15kg pack sizes comprising resin base and hardener components. 

Coverage

The coverage obtained will vary depending on the type and size of Aggregate used.

As a guide, the coverage should be a minimum of:

0.8Kg per m² on a Quartz Aggregate blind.

1.2Kg per m² on a Gripdeck Aggregate blind.

Storage

Store under dry warehouse conditions at a temperature between 15°C and 30°C.

Shelf Life

12 months in unopened, undamaged, sealed containers and stored under good conditions.

Technical Information

Working time @ 15°C20 minutes
Tack free time @ 15°C8 hours
Maximum overcoating time at 15°C30 hours
Full Cure @ 15°C
3 days
Hardness (Shore D)
80
Application Temperature Range
(do not apply if precipitation or
condensation is likely to result)
15 to 30°C
(do not apply if
the ambient or
floor temperature
is to fall below
10°C during the
first 24 hours)
Volume solids (%)100
EN 13813 Designation
SR-AR0.5-B2.0-IR10
Abrasion resistance
EN 13892-4
≤ 50 μm
Thermal compatibility (N/mm2)
EN 13687-1&2
≥ 1.5
Capillary absorption
EN 1062-3
≤ 0.1kg.m-2.h-0.5
Crack bridging ability
EN 1062-7; Static
≥ 500 μm
Impact resistance
EN ISO 6272-1
≥ 10 Nm
Adhesion by pull-off (N/mm2)
EN 1542
≥ 2.0
Slip/skid resistance*
≥ 55 units wet
* Medium aggregate blind

Application Instructions

MIXING 

Gripdeck Wearcoat comprises two components, a Resin Base and Hardener, which are supplied, pre-weighed in the correct proportions. Under no circumstances should part mixing be carried out.

Taking care to ensure that the bottom and sides are thoroughly scraped, transfer the entire contents of both components into a separate mixing container. Using a power whisk attached to a slow speed electric drill, mix for approximately 3 minutes ensuring the mixing head is pushed around the sides and bottom of the mixing container. Transfer the contents into another container,scraping down and re-mixing for a further 2 minutes avoiding the entraining of excessive air until a uniform consistency is obtained.

Never mix Gripdeck Wearcoat by hand as this could lead to areas of uncured material. Premixing of the resin component will aid mixing.

APPLICATION

On completion of mixing immediately apply the Gripdeck Wearcoat by squeegee followed by a short / medium pile roller at the required rate onto the pre-swept blinded surface.

Gripdeck Wearcoat is not colour stable and may discolour on ageing, especially the lighter colours. This will not adversely affect the performance of the system.

Gripdeck Wearcoat Plus should be used where light colours or a UV colour stable system is required.

CLEANING

Tools should be cleaned witt a suitable solvent immediately after use.

WORKING CONDITIONS

Gripdeck Wearcoat should not be applied at temperatures less than 15°C.

HEALTH AND SAFETY

Consult the appropriate Material Safety Data Sheets prior to using Gripdeck Wearcoat.

GENERAL GUIDANCE
This data sheet is for general guidance purposes only and may contain information that is inappropriate for certain conditions of use. Accordingly, all recommendations and suggestions are made without guarantee. Further information is available from our Technical Department.


Download file



Related products





Connect with Don Construction Products


  Complaints Record Form

  Customer Satisfaction

Name *
Email *
Phone
Address
Subject
Request  
Security Code *

Don Construction Products Ltd.

Headquarters
Hawthorn House, Helions Bumpstead Road,
Haverhill CB9 7AA, United Kingdom;
Tel: +44 1 4407 66360 
Fax: +44 1 4407 68897

Email: sara.harvey@dcp-int.co.uk
Email: stephen.bird@dcp-int.co.uk