Griptop PRIMER
Previous product
Next product
Griptop COVE PACK SEAL
 

Griptop
COVE PACK

COVING MATERIAL FOR WALL/FLOOR SURFACE JOINTS
 
Description:

Griptop Cove Pack is a three pack solvent free polyurethane based material that is used to form seamless radius coving at the junction between wall and floor surfaces.

Usage

Griptop Cove Pack is applied by trowel, is highly durable and when sealed with Griptop Cove Pack Seal has very good resistance to many of the chemicals commonly found in and industrial environment (consult our Technical Department for further details).

Materials Supplied

18kg. 

Coverage

Approximately 10 linear metres per kit at 150mm high and 6mm thick.

Storage

Store at temperatures between 5°C and 30°C.

Shelf Life

Approximately 6 months if stored in unopened containers and under good conditions.

Technical Information

EN 13813 DesignationSR-AR0.5-B2.0-IR4
Wear Resistance
EN 13892-4
≤ 50 μm
Bond strength (N/mm2)
EN 13892-8
≥ 2.0
Impact resistance
EN ISO 6272-1
≥ 4 Nm

Application Instructions

SURFACE PREPARATION

The surface must me clean, dry (less than 75% RH measured by hygrometer) and free of dust laitence, oils, paints or other forms of contamination (see the DCP Guide to Surface Preparation for further details).

PRIMING

Surfaces must be primed with Strongcoat Primer prior to application with Griptop Cove Pack. The Strongcoat Primer must be allowed to reach a tacky finish - typically 1-2 hours at 20°C.

MIXING 

Taking care to ensure that the bottom and sides are thoroughly scraped, transfer the entire contents of the Griptop Cove Pack Part B container into the Part A container and, using a Jiffy-type mixer attached to a slow running electric drill, mix for approximately two minutes. Once the Griptop Cove Pack parts A and B have been mixed, transfer the entire contents of the Part A container into a Casco or Cretangle-type mixer, taking care to ensure that the bottom and sides are thoroughly scraped.

Start the mixer and transfer to it the entire contents of the Griptop Cove Pack part C container, taking care to ensure that these are completely dry and lump-free.

Continue mixing for approximately two minutes.

Never mix Griptop Cove Pack by hand as this could lead to areas of uncured material.

APPLICATION

Once mixing is complete, transfer the Griptop Cove Pack to the primed surface and, using a combination of straight-edged and coving trowels, apply it evenly over this.

Once cured apply two coats of Griptop Cove Pack Seal (See Product Data Sheet for information) to provide extra protection for the cove. 

WORKING TIME

Griptop Cove Pack has a working time of approximately 15 minutes at 20°C.

Never leave the mixed Griptop Cove Pack kit to stand for any length of time prior to application as this will considerably shorten its working time.

CLEANING

Once mixing and application are complete, tools can be cleaned with a suitable solvent.

CURING TIME

At 20°C, Griptop Cove Pack should be touch dry in about 24 hours and allow 5 days before exposing it to chemical contamination (consult our Technical Department for details of curing times at other temperatures).

WORKING CONDITIONS

Griptop Cove Pack should not be applied at temperatures less than 10°C.

HEALTH AND SAFETY

Consult the appropriate Material Safety Data Sheets prior to using Griptop Cove Pack.

GENERAL GUIDANCE
This data sheet is for general guidance purposes only and may contain information that is inappropriate for certain conditions of use. Accordingly, all recommendations and suggestions are made without guarantee. Further information is available from our Technical Department.


Download file



Related products





Connect with Don Construction Products


  Complaints Record Form

  Customer Satisfaction

Name *
Email *
Phone
Address
Subject
Request  
Security Code *

Don Construction Products Ltd.

Headquarters
Hawthorn House, Helions Bumpstead Road,
Haverhill CB9 7AA, United Kingdom;
Tel: +44 1 4407 66360 
Fax: +44 1 4407 68897

Email: sara.harvey@dcp-int.co.uk
Email: stephen.bird@dcp-int.co.uk